User manual ver. 20210530
This document collects information on the safety, installation and use of the Temperature Sensor device.
Device description
The AURATON Temperature Sensor outdoor is a temperature sensor with a measurement resolution of 0.1°C for outdoor use. It is a battery-powered device that provides up to 2 years of continuous operation. Designed for use with the AURATON Pulse control unit.
- signal diode
- temperature sensor
- holes for mounting bracket
- pairing button
Device assembly
- Two 5 mm diameter holes should be drilled in the wall (the hole spacing should be measured using the mounting bracket included with the device).
- Insert the expansion bolts (included).
- insert the mounting bracket into the silicone seal
- Screw the mounting bracket with the gasket installed to the wall.
- Press the device onto the mounting bracket so that the holes on the back wall align with the latches on the bracket.
The mounting bracket with the seal applied can also be mounted using double-sided tape appropriate to the substrate material.
Battery replacement
If the battery in the device is discharged, replace it with a new CR2032 3V battery. To do this, unscrew the four screws securing the rear cover of the housing. Then, remove the plate located at the bottom of the housing and use a flat-blade screwdriver to remove the battery located in the battery holder. Press the new battery into the battery holder. After replacing it, reinsert the plate into the housing and screw the rear cover back onto the housing.
Device functions
Device:
- measures temperature with a resolution of 0.1 degrees,
- works up to 2 years on one battery,
- is equipped with a replaceable CR2032 3V battery,
- signals its operation with a two-color LED,
- creates a secure radio connection with other devices using the AURA protocol.
Description of measured parameters:
Temperature – current temperature with a measurement resolution of 0.1 degrees
Battery level – battery level expressed in %
Device pairing
Enabling pairing – Temperature Sensor
- Function button.
To activate pairing, use the included "stick" to hold down the button located on the back of the device, as shown in the diagram. Release the button when the LED lights up green. The pairing process should begin, and the LED should flash green. During this time (approx. 30 seconds), initiate pairing on the other device you want to pair with the Temperature Sensor.
Enabling pairing – AURATON Pulse control panel
Pairing in AURATON Pulse is enabled using the AURATON Smart App. On the next screen, name the device you're adding. After entering the name, press the "Add" button. Once successfully paired, you can place the device in any previously added room and add it to your favorites.
Factory reset
To restore factory settings, hold down the function button during normal operation (approx. 5 seconds) until the LED lights red. Release the button and press it again within 3 seconds to confirm the operation. All information on the device will be cleared.
Control via the AURATON Smart application
From the AURATON Smart application you can view the current temperature and battery level expressed as a percentage.
Restoring a previous software version
After performing an update or if it fails, it is possible to restore the previous version of the software.
To restore the previous software version, hold the button for at least 7 seconds until the LED turns orange, then release the button. Then, while the LED remains lit, hold the button again.
Technical data
| temperature range : | -20 – 45 °C |
| Temperature measurement range: | -20 – 45 °C |
| Temperature measurement resolution: | ±0.1 °C |
| Operating status check: | LED |
| Maximum number of paired devices | 3 |
| Power supply: | 3V CR2032 battery |
| Cooperation with the Internet headquarters | AURATON Pulse |
| Degree of protection: | IP42 |
| Frequency: | 868.150 MHz 868.450 MHz |
| signal strength : | Up to 11 dBm |
| Radio receiver category: | 2 |
| Range of action: | In a typical building, with a standard wall construction – up to 30 m, in an open area – up to 300 m |
| Dimensions [mm]: | 75 x 35 x 14 |
O
Devices are marked with a crossed-out waste bin symbol. In accordance with European Directive 2012/19/EU and the Waste Electrical and Electronic Equipment Act, this marking indicates that this equipment, after its useful life, must not be disposed of with other household waste.
Users are obligated to dispose of it at a collection point for used electrical and electronic equipment.
LARS Andrzej Szymański hereby declares that the Temperature Sensor radio equipment type complies with Directives 2014/53/EU and 2011/65/EU. The full text of the EU declaration of conformity is available in the download section below.
Manufacturer's address and contact details:
LARS, ul. Świerkowa 14
64-320 Niepruszewo
www.auraton.pl